Boral Gutter Replacement Nationwide

Boral Gutter Replacement: The Fort Lauderdale Owner’s Guide

Boral gutter replacement in Fort Lauderdale typically runs $14 to $28 per linear foot installed, with most single-story homes landing between $850 and $1,900 for a full run replacement. We stock Boral-compatible gutter components and install them regularly, and most replacements are completed in a single visit. You usually discover the problem the hard way: a sagging section pulling away from the fascia board, water spilling over the edge during one of our summer downpours, or a rust-through that leaves a steady drip against the house.

Call (754) 354-8628

If you’re seeing any of that, you’re in the right place. We’ll walk through exactly what fails on Boral gutter systems in South Florida, what a fair replacement costs, and whether you should grab a ladder or grab your phone.

Key Takeaways:

• Boral gutter replacement in Fort Lauderdale averages $14 – $28 per linear foot installed.
• Most full-run replacements take 3 to 5 hours and we finish same-day.
• Boral uses aluminum and steel gutter profiles in standard 5-inch and 6-inch K-style dimensions, so replacement parts are readily matched.
• Coastal salt air and hurricane-season wind shear are the two biggest killers of gutter systems here.

Which Boral Models This Applies To

Boral manufactures gutter profiles in two configurations that we see across Fort Lauderdale homes: 5-inch K-style aluminum and 6-inch half-round steel, with occasional copper runs on higher-end builds near Las Olas Boulevard and Victoria Park. The 5-inch K-style is by far the most common on single-family homes, while the 6-inch half-round shows up on older Mid-Century Modern properties and some custom builds in Bay Colony and Rio Vista.

Identifying your Boral gutter profile takes about thirty seconds. Look at the end cap and measure the opening width. Five inches across means K-style; a true half-circle shape means half-round. The gauge matters too: Boral aluminum runs .027 to .032 gauge depending on which line was installed. Here’s the gotcha we run into regularly: some Fort Lauderdale homes have Boral’s heavier .032 gauge on the front elevation and lighter .027 gauge on the back. A roofer who doesn’t check will slap mismatched gauge on your home, and you’ll get visible seams and uneven expansion in the heat. We measure every section before ordering.

OEM Boral sections are fine when they’re available, but for most Fort Lauderdale replacements we recommend a quality aftermarket aluminum that matches the profile and gauge precisely. The reason is practical: aftermarket stock arrives faster, costs 20 to 30 percent less, and carries the same 20-plus year material lifespan when properly installed. We also stock GAF, Owens Corning, and CertainTeed gutter components for homes with mixed-brand systems.

Signs Your Boral Gutter Replacement Is Failing

• Sagging or pulled-away sections. The hidden hangers or spikes have backed out of the fascia board. Fort Lauderdale’s heat cycles expand aluminum against the fasteners, and after enough seasons they work loose. Water then pools instead of draining, and the added weight makes the sag worse.
• Rust-through or pinhole leaks. On steel Boral half-round gutters, salt air from the Atlantic eats through the coating within 10 to 14 years. You’ll see a brown streak down the side of the house or drips from the underside of the gutter on rain-free mornings.
• Water spilling over the edge during rain. This is almost always a pitch problem. The gutter has settled out of slope, and South Florida’s afternoon downpours overwhelm it in seconds. Standing water then accelerates corrosion and breeds mosquitoes. Not great in Broward County.
• Visible seams separating. Boral sectional gutters rely on lap joints and sealant. Sealant fails in the Fort Lauderdale sun within three to five years, and each separated seam becomes a drip point right against your fascia.
• Fascia board rot behind the gutter. When a gutter leaks against the fascia for long enough, the wood behind it rots. By the time you see paint blistering or soft spots at the gutter line, you’re likely replacing fascia board along with the gutter run.

Replacement Cost & What’s Included

For Fort Lauderdale single-story homes, expect to pay $14 to $22 per linear foot for 5-inch K-style aluminum replacement, including removal of the old run, new hangers every 24 inches, seam sealing, downspout reconnection, and haul-away. Two-story homes with steeper roof access run higher, typically $18 to $28 per foot, because setup and safety equipment take longer. A typical 40-to-60-foot run on a single-story rancher in Wilton Manors or Coral Ridge lands between $850 and $1,300.

Every Boral gutter replacement we quote includes the full written price before we start. No change orders. No “we found more once we got up there” conversations. The number on your written quote is the number on your invoice. Each replacement is covered by our 365-Day Done Right Promise: if anything fails within a full year, we come back and fix it at no charge. That’s in writing, on every job, included by default.

DIY or Call Us?

Here’s the honest split. A homeowner on a single-story home can safely inspect gutters with a ladder, a tape measure, and a level. You can identify the profile size, check for standing water, and spot separated seams. That’s where DIY should stop. Replacing gutter runs involves working from the roof edge or a ladder while wrangling 20-foot sections of aluminum in the wind. Fort Lauderdale’s afternoon gusts turn a long gutter section into a sail. The injury risk from a fall or a dropped section is real, and the fascia-board damage from a bad DIY install costs more to fix than the gutter replacement itself.

If you want the work done right, call (754) 354-8628 and we’ll come measure, price it in writing, and get it done.

FAQs